Presidor™ Intelligent Power Control

Panels can be custom-built with selected modules pre-installed at the factory in your chosen order. Module choices are dual relay, quad relay, or quad dimmer. Our Intelligent dimmers feature state-of-the-art reverse phase control, are rated at 600W, and support full-range dimming (1–100% DMX) for both LED and incandescent loads. Air-gap relays turn ON and OFF at selectable DMX thresholds ranging from 10% to 90%. 0-10VDC analog outputs can be programmed as a source or sink to permit direct drive of analog ballasts. Sensing protection on all circuits includes overload, short-circuit, temperature, over-voltage, inductive load, and more, ensuring circuit safety. LED indication and real-time error report back to the command control, providing advanced feature reporting that is typically only found in very expensive dimmers. The Presidor™ Command Controller delivers a full-color, capacitive touch GUI for easy setup and automatic error reporting. Smart capabilities and intuitive operation make these panels unique.

Module Types

How to Order

Select Lighting Control Relay Panel Size based on the maximum number of modules/channels possible:

Model	Product Description/Maximum Output Capacity
PP-8	2 modules or 8 channels maximum
PP-12	3 modules or 12 channels maximum
PP-24	6 modules or 24 channels maximum

1. Select panel size between choices 8, 12, or 24.
2. Select voltage input between choices of 120/208 or 120/240.
3. Select output/module type in order from top to bottom between choices L, 4, 2, or A.
4. Select the disconnect breaker option (DB) if applicable.

Ordering Information

Model	Product Description/Maximum Output Capacity
PP-8	Small panel, 2 module capacity, Maximum 8 load circuits, Maximum capacity 4,800 Watts.
PP-12	Small panel, 3 module capacity, Maximum 12 load circuits, Maximum capacity 7,200 Watts.
PP-24	Large panel, 6 module capacity, Maximum 24 load circuits, Maximum capacity 14,400 Watts.
DB	Optional 3P40A Disconnect Breaker.
Type L	Quad LED Dimmers, 4 x 600W Intelligent Dimmers. Maximum capacity 2,400 Watts.
Type 4	Quad Air-Gap Relays, 4 x 600W Intelligent Relays. Maximum capacity 2,400 Watts.
Type 2	Dual Air-Gap Relays, 2 x 1,200W Intelligent Relays. Maximum capacity 2,400 Watts.
Type A	Airflow/Block-off. Permits future panel capacity expansion.

Presidor™ LED Dimmer & Relay Panels

Presidor™ PP-8 & -12

Base Specifications

Voltage: 100 – 240 VAC operational range at 50 or 60 Hz
Power Consumption: 11 Watts (idle) ie. 400mWatt / Channel
Cabling: RS485 Cat5/5e/6 cable or retrofit into existing Belden#9773 or equivalent, 300m Max (1000′).
Dimensions: 18.7″ W x 22.1″ H x 4.5″ D (476mm x 561mm x 112mm)
Weight: +-40 lbs ( +-18Kg)

Presidor™ PP-24?

Base Specifications

Voltage: 100 – 240 VAC operational range at 50 or 60 Hz
Power Consumption: 11 Watts (idle) ie. 400mWatt / Channel
Cabling: RS485 Cat5/5e/6 cable or retrofit into existing Belden#9773 or equivalent, 300m Max (1000′).
Dimensions: 18.7″ W x 32.2″ H x 4.5″ D (476mm x 817mm x 112mm)
Weight: +-60 lbs ( +-27Kg)

Specifications

• Available in Single and Three Phase.
• Dim Standard: LED Dimmable and Incandescent.
• Relay for Non-Dim.
• DMX-512 start addressable in single channel (offset) or individually(patch).
• Embedded programming with Binary addressing of each module.
• Intelligent fault/error reporting: Short, inductive, Overload, and more.
• Intelligent feedback on Input Voltage and Frequency in Hz.
• Intelligent feedback per channel on loading capacity in Watts.
• Intelligent feedback on total load for the rack in watts.
• User-adjustable Curve/Trip Set for LED fixtures with different turn-on points.
• Programmable Fire setup.
• Capacitive Touch display for easy setup and configuration.

• Intuitive navigation allows for ease of operation.
• Opto-Isolated DMX IN and Through.
• Fire Aux Input.
• Overheat and overcurrent protection.
• Analog 0-10VDC Source or Sink 100mA relay only.
• State-of-the-art high-speed, low-power “green” processor and ancillary circuitry with a power consumption of >
• 400mA / Channel.
• 24 VDC for powering External Controls PWS-20P or PWS-70P.
• No Laptop required for setup.
• Optional: BMS or Network node ready.
• Comply with UL508A standard.
• Patent Protected.

Technical Specifications

• 1.0 PRESIDOR TM – Panel shall be capable of handling Dimmers and Relays in the same enclosure.
• 1.1 On power-up, the panel will perform a self-test.
• 1.2 PRESIDOR TM Panel shall be capable of dimming incandescent, quartz, and LED dimmable fixtures.
• 1.3 PRESIDOR TM Panel shall be powered from 120/208 VAC 3-Phase 5-Wire or 120/240 VAC 1-Phase 4-Wire.
• 1.4 A capacitive touch interface for ease of setup and monitoring. All programming shall be via a user-friendly, intuitive, and self-prompting menu structure. No PC or special software will be required.
• 1.5 DMX-512 start address shall be addressable in single channel (offset) or individually (patch) on a per circuit/dimmer/channel basis. It shall be possible to address any dimmer to any channel within the entire DMX-512 universe or all dimmers to a single DMX channel.
• 1.6 Dedicated DMX In and DMX Thru ports shall be supplied internally via 3-Pin break-away connectors.
• 1.7 An active over-temperature shall illuminate a fan symbol at an internal temperature of 40 °C. In the event that the temperature run away, there will be an automatic shutdown of all the dimmer circuits at 70 °C.
• 1.8 PRESIDOR TM Panel shall employ the “system-on-a-chip” advanced digital technology. The control electronics shall be contained on a single PCB capable of driving 4 channels. Advanced state-of-the-art hardware and firmware will ensure >1% accuracy on all dimmer outputs.
• 1.9 The DMX inputs shall comply with USITT DMX-512-A (ANSI E1.11-2008), the standard protocol for digital data control.
• 1.10 PRESIDOR TM Panel shall be capable of reading the system AC Voltage and frequency on the UIB.

• 1.11 PRESIDOR TM Panel shall be capable of reading individual channel loading in Watts.
• 1.12 PRESIDOR TM Panel shall be capable of reading the complete loading of the panel in Watts.
• 1.13 PRESIDOR TM Panel shall be capable of setting the curve/trip set.
• 1.14 PRESIDOR TM Panel shall be capable of self-configuring module types by the press of a single button.
• 1.15 PRESIDOR TM Panel shall be capable of having a user and Admin password for the protection of configuration data.
• 1.16 PRESIDOR TM Panel shall be capable of showing the Firmware version on the UIB.
• 1.17 PRESIDOR TM Panel shall be capable of resetting the panel controller via the UIB.
• 1.18 PRESIDOR TM Panel shall be capable of selecting channels for the fire alarm to be activated at Full on in the event of a Fire alarm.
• 1.19 PRESIDOR TM Panel shall have a lockable hinged lid.
• 2.0 All printed circuit boards (PCB’s) shall be FR4/G10 with a UL 94V-0 Flame Class Rating.
• 2.1 PRESIDOR TM Panel shall be ETL listed and comply fully with UL508A and CSA.